Joystick

Wiring for joysticks

Brook Hitbox Cable
New
Cable Brook Hitbox
In Stock
Cable for Hitbox allowing to replace a joystick by buttons.
5-pin male connector to be plugged into the original 5-pin connector (arcade stick or cabinet). Opposite 2.8mm lug connectors for button connection.
Can be used with Brook Fighting Board cable for full hitbox wiring on a Brook board (Fighting board PS3 / PS4 Plus, Fighting board PS4 + audio, Fighting board ZeroPi, Universal Fighting board with connectors).
Pandora Box 4.8mm GPiO Cable
Pandora Box 4.8mm GPiO Cable
In Stock
Specific cable for 2 players Pandora Box PCB. Connectors for 4.8mm buttons and joysticks. Connectors for power supply.
Pandora Box 2.8mm GPiO Cable
Pandora Box 2.8mm GPiO Cable
In Stock
Specific cable for 2 players Pandora Box PCB. Connectors for 2.8mm buttons. 5 pin connectors for joysticks. Connectors for power supply.
6.3mm mass chain - Dupont
Pack
6.3mm mass chain - Fork thimble
In Stock
Common ground chain with fork lug connector for connection to an arcade power supply with terminal block. For the wiring of the mass of the leds supports of your illuminated buttons. 29 connectors 6.3 1 fork lug connector
2.8mm mass chain - Dupont
2.8mm mass chain - Dupont
In Stock
Common ground chain with Dupont connector for connection to the GPiO bus of a raspberry Pi. For wiring the earth of buttons and joysticks. 30 connectors 2.8 1 Dupont connector
Weight chain 4.8mm - Dupont
Weight chain 4.8mm - Dupont
In Stock
Common ground chain with Dupont connector for connection to the GPiO bus of a raspberry Pi. For wiring the earth of buttons and joysticks. 30 connectors 4.8 1 Dupont connector
Joystick cable 5 pins - Dupont
Joystick cable JLF-H 5 pins - Dupont
In Stock
Joystick cable JLF-H 5 Dupont connectors for the connection of a joystick equipped with a 5 pins connector (Sanwa or luminous) to the GPiO bus of a Raspberry pi. Length: 80cm.
AWG 22 electronic cable - Black
AWG 22 electronic cable - Black
In Stock
For your electronic assemblies, buttons, joysticks, LEDs Section: 0.326mm2 NOT SUITABLE FOR POWER SUPPLY
AWG 22 electronic cable - Yellow
AWG 22 electronic cable - Yellow
In Stock
For your electronic assemblies, buttons, joysticks, LEDs Section: 0.326mm2 NOT SUITABLE FOR POWER SUPPLY
AWG 22 electronic cable - Red
AWG 22 electronic cable - Red
In Stock
For your electronic assemblies, buttons, joysticks, LEDs Section: 0.326mm2 NOT SUITABLE FOR POWER SUPPLY
5 pins joystick cable for usb encoder
5 pins joystick cable for usb encoder
In Stock
Joystick cable for usb encoder JST XH 5 pins connectors To connect a joystick equipped with a 5-pin JST port to a USB encoder Length: 20cm
Joystick or button cable for usb encoder
Joystick or button cable for usb 4.8mm encoder
In Stock
Joystick / button cable for usb encoder 4.8mm terminals JST XH 2 pins connector To connect a button or a joystick switch to a USB encoder Length: 22cm
Joystick cable 5 pins
Joystick cable JLF-H 5 pins
In Stock
Cable for JLF-H joystick with 5 pins connector and tinned wires. Allows the connection of a joystick fitted with a 5-pin male connector. Tinned wires at the other end: possibility of crimping lugs or dupont connector. Length: 50cm
Common mass chain - 4.8mm
Common mass chain - 4.8mm
In Stock
For wiring the earth of HAPP buttons and joysticks. 4.8mm connectors Number of connectors: 30
Common mass chain - 6.3mm
Common mass chain - 6.3mm
In Stock
For the wiring of the mass LED supports of the illuminated buttons (HAPP models to be assembled). 6.3mm connectors. Number of connectors: 30
Common mass chain - 2.8mm
Common mass chain - 2.8mm
In Stock
For wiring the earth of buttons and joysticks. 2.8mm connectors for AIO buttons. N umber of connectors: 30