Buttons wiring

Buttons wiring

Brook Hitbox Cable
Cable Brook Hitbox
In Stock
Cable for Hitbox allowing to replace a joystick by buttons.
5-pin male connector to be plugged into the original 5-pin connector (arcade stick or cabinet). Opposite 2.8mm lug connectors for button connection.
Can be used with Brook Fighting Board cable for full hitbox wiring on a Brook board (Fighting board PS3 / PS4 Plus, Fighting board PS4 + audio, Fighting board ZeroPi, Universal Fighting board with connectors).
Pandora Box 4.8mm GPiO Cable
Pandora Box 4.8mm GPiO Cable
In Stock
Specific cable for 2 players Pandora Box PCB. Connectors for 4.8mm buttons and joysticks. Connectors for power supply.
Pandora Box 2.8mm GPiO Cable
Pandora Box 2.8mm GPiO Cable
In Stock
Specific cable for 2 players Pandora Box PCB. Connectors for 2.8mm buttons. 5 pin connectors for joysticks. Connectors for power supply.
LED power harness 5V 12V 6.3mm
Power supply harness LED buttons 5V 12V 6.3mm
In Stock
Cable harness for 5V or 12V LED button power supply 5V: Allows you to connect up to 10 LEDs directly from a USB joystick encoder with the connector provided. 12V: change the connector with 2 fork terminals, for example, to be connected to an arcade power supply. We can make this adaptation for you. In this case, ask us.
Brook fighting board cable
Brook cable fighting board
In Stock
Cable for connecting your button and joystick to the Brook Fighting Board universal controller card. Preserve the original connections of your arcade stick. Replace the cables with those from this kit and simply connect everything to the Universal fighting board.
6.3mm mass chain - Dupont
Pack
6.3mm mass chain - Fork thimble
In Stock
Common ground chain with fork lug connector for connection to an arcade power supply with terminal block. For the wiring of the mass of the leds supports of your illuminated buttons. 29 connectors 6.3 1 fork lug connector
2.8mm mass chain - Dupont
2.8mm mass chain - Dupont
In Stock
Common ground chain with Dupont connector for connection to the GPiO bus of a raspberry Pi. For wiring the earth of buttons and joysticks. 30 connectors 2.8 1 Dupont connector
Weight chain 4.8mm - Dupont
Weight chain 4.8mm - Dupont
In Stock
Common ground chain with Dupont connector for connection to the GPiO bus of a raspberry Pi. For wiring the earth of buttons and joysticks. 30 connectors 4.8 1 Dupont connector
AWG 22 electronic cable - Black
AWG 22 electronic cable - Black
In Stock
For your electronic assemblies, buttons, joysticks, LEDs Section: 0.326mm2 NOT SUITABLE FOR POWER SUPPLY
AWG 22 electronic cable - Yellow
AWG 22 electronic cable - Yellow
In Stock
For your electronic assemblies, buttons, joysticks, LEDs Section: 0.326mm2 NOT SUITABLE FOR POWER SUPPLY
AWG 22 electronic cable - Red
AWG 22 electronic cable - Red
In Stock
For your electronic assemblies, buttons, joysticks, LEDs Section: 0.326mm2 NOT SUITABLE FOR POWER SUPPLY
Button cable for usb encoder
Button cable for usb encoder 2.8mm
In Stock
Button cable for usb encoder 2.8mm terminals JST connector To connect a button to a USB encoder Length: 22cm
Joystick or button cable for usb encoder
Joystick or button cable for usb 4.8mm encoder
In Stock
Joystick / button cable for usb encoder 4.8mm terminals JST XH 2 pins connector To connect a button or a joystick switch to a USB encoder Length: 22cm
Molex 12V LED power harness
Power supply harness Molex 12V LED buttons
In Stock
Wiring harness for 12V LED button power supply. Allows you to connect up to 30 LEDs directly from an ATX pc power supply. 6.3mm insulated terminals.
Molex 5V LED power harness
Power supply harness 5V Molex LED buttons
In Stock
Wiring harness for 5V LED button power supply Allows you to connect up to 18 LEDs directly from an ATX pc power supply 2.8mm insulated terminals
5V 12V LED power harness
Power supply harness LED buttons 5V 12V 2.8mm
In Stock
Wiring harness for 5V or 12V LED button power supply. 5V: Allows you to connect up to 10 LEDs directly from a USB joystick encoder with the connector provided. 12V: change the connector with 2 fork terminals, for example, to be connected to an arcade power supply. We can make this adaptation for you. In this case, ask us.
Common mass chain - 4.8mm
Common mass chain - 4.8mm
In Stock
For wiring the earth of HAPP buttons and joysticks. 4.8mm connectors Number of connectors: 30
Common mass chain - 6.3mm
Common mass chain - 6.3mm
In Stock
For the wiring of the mass LED supports of the illuminated buttons (HAPP models to be assembled). 6.3mm connectors. Number of connectors: 30
Common mass chain - 2.8mm
Common mass chain - 2.8mm
In Stock
For wiring the earth of buttons and joysticks. 2.8mm connectors for AIO buttons. N umber of connectors: 30

Seimitsu PSL-H microswitch cable
Seimitsu PSL-H microswitch cable
In Stock
Cable to connect the micro-swicth with integrated led MM9-PSU-5V. For Seimitsu PS-14-KN buttons Length: 50cm